Generators

?

?

?

Autocode wireless remote controller / universal spare parts for

?

?

car parking heaters

?

?

?



?

?

?

?

?

?

?

Notes:

?

?

This remote controller is used for Belief parking heater. If you need

?

this, please contect me firstly to comform wether the controller

?

could be used on your heater.

?

?

?



?

5.3.4 Instruction for installation
?

According to the diagram of the wireless remote control receiver connect the wiring of remote

control receiver,manual button and install (tight) the receive/transmitting antenna before use.
?

5.3.5 Instruction for operation


5.3.5.1 Light up and go out of the screen


5.3.5.1.1 Screen and all the symbols light up after the battery is installed ,then the remote controller enters the standby state(Screen goes out and none of the symbols are displayed after 2 seconds).


5.3.5.1.2 In all processes ,the remote controller will enter the key lock state automatically if no operation within 10 seconds .Key lock symbol occurs and the screen goes out.


5.3.5.1.3 Unlocking method: When the screen goes out, hold down the stop key for 3 seconds ,it will be unlocked. Then the screen lights up and the symbol of the key lock disappeared.


5.3.5.1.4 In the heating state, the heating symbol,rest of heating time,whole heating time and screen state(lock or unlock) occurs on the screen .Press any key,the screen will be lighted up (key lock symbol will be displayed).


5.3.5.2 The autocode function of remote controller and wireless remote control receiver


5.3.5.2.1 Press the encoding button of the wireless remote control receiver, the indication light will turn red and the remote controller will enter into the encoding state.


5.3.5.2.2 In the encoding process of wireless remote control receiver ,encode the four different remote controllers by pressing each four different keys(in the unlocked status)of the remote controllers .Heating symbols(15mins ,30mins ,45mins) will all light at the same time if the
encoding operation is correct. All the heating symbols will go out after 1 seconds and indication light turns green if encoding set up successfully.


5.3.5.3 The starting of parking heater


5.3.5.3.1 In standby and unlocking status,press the key of“heating 15 minutes”,then the screen is lighted up and the indication light flashes one time.If the Heating 15 minutes symbol is lighted up,the operation is finished.The time of heating 15 minutes is displayed on the screen and the
heater enters into the heating status.If the heating 15 minutes symbol is not lighted up,the operation failure.Please re-press the key of heating 15 minutes.


5.3.5.3.2 In standby and unlocking status,press the key of“heating 30 25 minutes”,then the screen is lighted up and the indication light flashes one time.If the Heating 30 minutes symbol is lighted up,the operation is finished.The time of heating 30 minutes is displayed on the screen and the
heater enters into the heating status.If the heating 30 minutes symbol is not lighted up,the operation failure.Please re-press the key of heating 30 minutes.


5.3.5.3.3 In standby and unlocking status,press the key of“heating 45 minutes”,then the screen is lighted up and the indication light flashes one time.If the Heating 45 minutes symbol is lighted up,the operation is finished.The time of heating 45 minutes is displayed on the screen and the heater enters into the heating status.If the heating 45 minutes symbol is not lighted up,the operation failure.Please re-press the key of heating 45 minutes.


5.3.5.4 The shutdown of parking heater


5.3.5.4.1 In the heating status,the remaining heating time is gradually decreased by the heating process.The heater will stop heating when the remaining heating time is cleared to zero or press the stop key in the unlocking status.when the stop operation is set,the screen will be lighted up and heating symbol will be went out.The heating process will be stop after the end of heating symbol occurs and the buzzer rings two times.


5.3.5.4.2 In the heating end of unlocking status,press stop key,the remote controller will return to the standby and locking status immediately.


5.3.5.4.3 In the heating end of locking status, the remote controller will return to the standby and locking status after 60 seconds.


5.3.5.5 Heating key operation in the heating status


5.3.5.5.1 In the heating of unlocking status,press the key of heating 15 minutes,the screen is lighted up and the heating 15 minutes symbol is displayed.The remaining heating time can’t be accumulated,the cutdown from 15 minutes to begin again.


5.3.5.5.2 In the heating of unlocking status,press the key of heating 30 minutes,the screen is lighted up and the heating 30 minutes symbol is displayed.The remaining heating time can’t be accumulated,the cutdown from 30 minutes to begin again.


5.3.5.5.3 In the heating of unlocking status,press the key of heating 45 minutes,the screen is lighted up and the heating 45 minutes symbol is displayed.The remaining heating time can’t be accumulated,the cutdown from 45 minutes to begin again.