Electronics Agents

Pitch 7.92mm Pcb Connectors Wire To Board Single Row 2 Pin Housing Lock For TV Set
?
1. Product??Informations:?
Housing Material: Nylon 66, UL 94-V0,
Housing color: White/Black/yellow
Housing Pin NO.: 2Pin,single row ; P/N:A3961H-02P-2
Terminal Material: Brass,(P/N:A3961-TBE);Phosphor Bronze(P/N:A3961-TPE),
Terminal E-stamping before Tin-plated.
Terminal Wire Range: AWG#18--#22, Insulation O.D.: 3.0mm(max). Qty/Reel:4000pcs.
?
2. Specifications:
Current Rating: 7A AC,DC
Voltage Rating: 250V AC, DC
Tenperature Range: -25oC--+85oC
Contact Resistance:5MΩ Max
Insulation Resistance: 1000MΩ Min
Withstanding Voltage: 1500V AC/minute
?
3. Mechanical Performance
?

- - - -
Test Description | Procedure | Requirement |
5-1 | Actuator Insertion & Withdrawal Force | Insert and withdraw actuator at the speed rate of 25±3mm / minute. | Refer to paragraph 7 |
5-2 | Crimping Pull Out Force | Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) | AWG#16 | 10.2 kgf (Min.) |
AWG#18 | 8.16 kgf (Min.) |
AWG#20 | 6.12 kgf (Min.) |
AWG#22 | 4.08 kgf (Min.) |
5-3 | Terminal Insertion Force. | Insert the crimped terminal into the housing. | 1.50 kgf (Max.) |
5-4 | Terminal/Housing Retention Force. | Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. | 3.00 kgf (Min.) |
5-5 | Pin Retention Force | Apply axial pull out force at the speed rate of 25±3mm / minute. | 3.00 kgf (Min.) |
5-6 | Durability | When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. | Contact Resistance 20mΩ (Max.) |
5-7 | Vibration | Amplitude: 1.5mm P-P
Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes.
(Based upon MIL-STD-202 Method 201A) | Appearance No Damage.
Contact Resistance 20mΩ (Max.)
Discontinuity 1 μsec.(Max.) |
5-8 | Physical Shock | 490m/s2｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) |
- - - -

?
?
4. Environmental Performance And Others
?

- - - -
Test Description | Procedure | Requirement |
6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) |
6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) | Appearance No Damage.
Contact Resistance 20mΩ (Max.) |
6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) |
6-4 | Humidity | Temperature: 40±2℃
Relative Humidity : 90~95%
Duration: 96 hours
(Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) | Appearance No Damage.
Contact Resistance 20mΩ (Max.)
Insulation Resistance 500MΩ (Min.)
Dielectric Withstanding Voltage Must meet 4-3 |
6-5 | Temperature Cycling | 5 cycles of:
a) -55℃ 30 minutes
b) +85℃ 30 minutes
(Based upon JIS C0025) | Appearance No Damage.
Contact Resistance 20mΩ (Max.) |
6-6 | Salt Spray | Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101D Cond. B) |
6-7 | SO2 Gas | 24 hours exposure to 50±5ppm.
SO2 gas at 40±2℃. |
6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution |
- - - -

?
?

- - - -
6-9 | Solder-ability | Soldering Time: 5±0.5 sec.
Solder Temperature: 245±5℃ | Solder Wetting 95% of immersed area must show no voids, pin holes |
6-10 | Resistance to Soldering Heat | Solder pot method
Soldering time: 10±0.5 sec.
Solder Temperature: 260±5℃
Solder iron method
Soldering Time: 5±0.5 sec.
Solder Temperature: 370℃ ~ 400℃ | Appearance No Damage. |
- - - -

?
?
5. Actuator Insertion/Withdrawal Force

[Unit : kgf]

- - - -
Circuits | At Initial |
Insertion (Max.) | Withdrawal (Min.) |
Single | 2.5 | 0.20 |
02 | 5.0 | 0.40 |
- - - -

6. Drawing:
?