Electric Power Tools

Product Description
? ? ? ? Airlaid paper is a textile-like material categorized as a nonwoven fabric?made from fluff pulp.?The airlaid paper making machine is produce the airlaid paper. There are different airlaid paper making lines for the production of basic materials for soft and absorbent disposable products for the following industries and applications:
1. For home care, like napkins.
2. Medical applications
3. Industrial wipes
?
Technical specifications

- - - -
Width | 1800mm |
Capacity | about 12ton/24hr |
Weight | 70g/m2 |
Production rate | 180m/min |
Raw materail | baled fluff pulp, ES fibers, latex etc. |
Heating method | electric? |
Technology type | Latex bonded Airlaid type |
- - - -

?
Application of final product
1. Airlaid paper wipes
2. Airlaid paper for household cieaning and wipes
3. Airlaid paper for industrial cleaning and wipes
4. Airlaid paper for kitchen wipes
5. Airlaid absorbent paper for kitchen use
6. Oil absorbent airlaid paper wipes
7. Oil absorbent airlaid paper
8. airlaid paper for car cleaning cloth
?
Structural characteristics
? ? ? ? Automatic control of the whole machine, automatic feeding of raw materials, direct supply of quantitative, Reduce the static electricity generated by the long cycle; No blind spot low static crushing system grinding system, Can be completely grind all kinds of pulp board, does not destroy the pulp fiber length, automatic compaction, automatic winding, PLC a key to start, a key stop.
?
Operational principle
? ? ? ? This equipment is based on the principle of & quot;long network operation, airlaid forming, hot air penetration& quot;:
The wood pulp were used as raw materials, will be brinded after brinding system, feeding to the Storage tank. Then feeding in to forming part by the Batching machine.The short fibers were used as raw materials, feeding into the brinding machine by Automatic feeding machine. After brinding, feeding into the forming part by Direct feeding type batching machine.Then the mix wood pulp and fiber are lapped by airlaid forming machine, through the Excessive part, go into the heating part, cooling part and paper will automatically change the volume by Automatic winding and changing roll part.
Start the wood pulp feeding system and fiber feeding system, wood pulps and fibers are feeding into forming part by feeding fans. According to the adsorption of the molding box to achieve uniform blanking, and the formation of paper. The paper passed through the main forming part, Excessive part, and heating part. In the heating part the hot air melt the PE of the fiber, in order to achieve the purpose of bonding the wood pulp fiber. And finally complete the paper roll by the winding machine.
# The pulp was treated with the treated pulp, and ES fiber was selected as a two-component fiber of PE/PP. Adding ES fiber 20-25%, wood pulp fiber proportion of the 75-80%, The increase of ES fiber ratio, Zorbcor strength increases but the water absorption decreased, on the other hand, reduces the intensity of dust and increased.
# The air heating temperature of the oven is controlled at 140-145℃, which is used for the outer PE of the ES material in the melting paper, but can not melt the inner layer PP.

Final product

?
Installation and commissioning
? ? ? ?The Seller sends 3-4 personnel (electrical, mechanical assembly, training and guidance personnel) to guide the installation, commissioning. The Buyer shall arrange 5-8 person for installation. The installation and commissioning time is 30 days. The Buyer shall be responsible for the wages, allowances, accommodation and related expenses of the seller& acute;s installers. During installation, the Buyer shall be equipped with 5T forklift, elevator, or professional installation team.
?
requirements for workshop
? ? ? ? The workshop space should not be less than L60m*W12m*H7m. The Buyer should give the Seller workshop diagrams with upright post, door, window, partition wall, upper and lower water, etc. In order to determine the installation and installation requirements.