Anti Static Digital Smd Rework Soldering Station , 75W 60HZ Air Soldering Station - M-75D
Anti Static Digital Smd Rework Soldering Station , 75W 60HZ Air Soldering Station For Sale, Most Competitive Price, Fast Delivery, Custom Service, Wholesale Anti Static Digital Smd Rework Soldering Station , 75W 60HZ Air Soldering Station, Made in China, High Quality Products!, China cheap prodocuts, china suppliers Supplier, Manufacturer.
?
75W Anti-static Knob Tempering Digital Display Soldering Iron Station 60HZ
?
?
YMK Low Frequency Soldering Station
?
YMK Low Frequency Soldering Station through electronic display board to control the heater work, so as to achieve the temperature control. The inside temperature sensor of heater detect the temperature signals into electrical signals, to the inside of the electronic display board microcomputer chip (MCU), through the analysis of the microcomputer chip processing, the output control signal control thyristor output or close the heater working power supply, so as to achieve the practical work of soldering iron temperature control.
?
?
Soldering Station Specification:?
?
- - - -
Power | 75W |
Output Voltage | AC24V |
Temperature Range | 200～480℃ |
Max Surrounding Temperature | 42℃ |
Temperature Stability | ±5℃ (no load) |
Shell Material | Aluminum Alloy |
Size | 110*105*165mm |
Net weight | 2.2KG |
- - - -
?
?
Solderin Iron Specification:
?
- - - -
Power consumption | 75W |
Tip-to-ground resistance | ＜2Ω |
Tip-to-ground voltage | ＜2mV |
Tip-charged body IR | ＞5MΩ |
Electromagnetic heating core | Resistance Heating |
Iron cord | 1.2m |
handle length | 20cm |
Weight | 85g |
- - - -
?
?
Setting ?New Temperature:
?
Revolving the knob to your desired temperature, next, display screen is showed your setting temperature and stay in screen 3 seconds, and the new temperature setting is finish. Check again the temperature of soldering tip for sure it in new temperature. 350~420℃ is suggested in soldering temperature range.
?
?
Calibrating Temperature of Soldering Tip
?
The soldering tip should be re-calibrated the temperature after changing the Tips or replacing the Heating Core and Soldering Iron. Please use Dedicated Iron Temperature Tester like 191/192 thermometer to adjust it, the procedure as below:
1) Set the temperature of Soldering Station to 350℃.
2) Use a straightedge (-) screwdriver or small plus (+) screwdriver to adjust the Trimmer Resistor which marked“CAL” keyhole in trimmer panel.
3) Turn the screw clockwise to increase the temperature and counterclockwise to reduce the temperature.
4) Keeping to adjust the trimmer resistor until the Station show the same temperature as the Temperature Tester’s temperature.
5) Use Temperature Tester check the soldering tip temperature again, it should be the right temperature , pls kindly note that +/-5℃ in Temperature Tester is in the standard tolerance.
Remark: this Calibrating must operated by specialized person.
?
?
Product?Service:
?
1. Good quality and reasonable price.
2. Technical assistance provided.
3. Professional service before and after sale.
4. All emails could be replied within 24 hours.
5. Skype video assisted any problem.
?
?
?
?
?
?
YMK Intelligent M&E Co.,Ltd
Address: Palais de fortune, ShaJing Block, BaoAn District, ShenZhen, China, ShenZhen, Guangdong, China, 518000
Tel: 86-755-23575730
YMK High Frequency Solding Station comply with most of Electronic Factory who require the high precision soldering,stable soldering temperature and big solder joints needing, less cost than Weller or Hakko and good function & better soldering effect.
